• Closed system for dust free operation
  • Integral; pre-weigh hopper on Twin Load Cell System
  • Radial or flap type inlet gate
  • -Flap gate for larger bulkier materials OR Radial gate to feed finer powder/ granular materials
  • Double bomb door discharge gates
  • Retractable Calibration brackets
  • Stabilizing Spring steel design
  • Aspiration facility provided
  • Totalizing of material throughput
  • Present batch out loading
  • Monitoring & control of material flow rate
  • Upstream & downstream interlocks
  • Panel Locks on Inspection doors
  • RS232 or RS485 serial interface for linking to PLC, SCADA or Printer
  • Running off 220v, Single Phase Electricity
  • Operating & Maintenance manual
  • Contact Parts Stainless Steel, 304 Stainless Steel, 316 Stainless Steel, 3CR12
  • Loading hopper with level control
  • Discharge chute with level control
  • AMIC (AccuTech Management information Centre)
  • Voltage Stabilizers (for areas with power surges)
  • Critical Spares Basket
  • Magnet
  • Suspended frames
  • Stainless Steel 304/316 Construction
  • International Shipping
  • Training Courses
  • Sampler Modification
  • Service Agreements
  • Choose color combination
  • Epsom Printer Configuration
  • Conveyors
  • Silo Level Control – Binmaster
  • Compressors
  • Calibration Weights
  • Machine Refurbishments
  • Check Scales

Typical Equipment Dimensions – TBC

Air Consumption – 40nl/m Clean Dry Air

Electrical Requirements – Input Voltage 110V AC-60Hz or 220V AC-50Hz

Power Consumption – 50W

Operator Pressure –  6-Bar -90PSI

Ambient Temperature –  -5°C – 48°C

Powder Coated Colors -Machine-Carrier Beige – Doors – RAL 5012 (others Optional)

AC30

AC60

AC90

AC120

AC150

AC200

AC300

AC500

AC800

AC1500

AC2000

The material enters the scale through the open inlet feed gate and is accumulated in the weigh hopper until a preset weight is reached. The inlet gate then closes and a short time period is allowed for the material to settle before the gross weight signal is read and recorded by the controller. The discharge gate is then opened and the material is discharged. The discharge gate is then closed. The controller reads the tare weight value and subtracts this from the gross weight value. The true nett weight is added to the scale total. This cycle is then repeated.

Designed for Milling, Silo’s, Vessels, Trains, Ports, anything industrial that requires a more accurate weighing than a weigh bridge

All Process Weighers include & integral AT-30 Processor Controller, which may be mounted remotely if required. The weigh hopper is suspended from two load cells and has a stabilizing mechanism to prevent movement during filling. Retractable calibration brackets are provided on the weigh hopper for ease of calibration.

The material enters the scale through the open inlet feed gate and is accumulated in the weigh hopper until a preset weight is reached. The inlet gate then closes and a short time period is allowed for the material to settle before the gross weight signal is read and recorded by the controller. The discharge gate is then opened and the material is discharged. The discharge gate is then closed. The controller reads the tare weight value and subtracts this from the gross weight value. The true nett weight is added to the scale total. This cycle is then repeated.

Process Weigher Chart Capacity

NOTE:
CAPACITIES FOR AC30,AC60,AC90 & AC120 BASED ON 5 TIPS/MIN.
CAPACITIES FOR ALL OTHER SCALES BASED ON 4 TIPS/MIN.
FOR AC200 THE FIGURES IN BRACKETS ARE BASED ON 5 TIPS/MIN AND ARE ONLY TO BE USED FOR FREE FLOWING PRODUCTS AFTER CONSULTATION WITH TECHNICAL DEPARTMENT

Process Weighing

Process weighers spares

[fusion_products_slider picture_size=”fixed” cat_slug=”at-30″ number_posts=”4″ carousel_layout=”title_below_image” autoplay=”yes” columns=”5″ show_nav=”yes” mouse_scroll=”no” show_cats=”no” show_price=”no” show_buttons=”yes” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” /]